Init fork from Stuart Robinson's repo

examples/SX128x_examples/Camera/240_StuartCAM_ESP32CAM/Settings.h

@@ -0,0 +1,92 @@
+/*******************************************************************************************************
+  Programs for Arduino - Copyright of the author Stuart Robinson - 19/03/22
+
+  This program is supplied as is, it is up to the user of the program to decide if the program is
+  suitable for the intended purpose and free from errors.
+*******************************************************************************************************/
+
+//updated pinouts for 'ESP32CAM_Long_Range_Wireless_Adapter PCB dated 271121
+//Note transistor driving the White LED on pin 4, or the LED needs to be removed
+
+#define NSS 12                //select on LoRa device
+#define NRESET 14             //reset pin on LoRa device
+#define RFBUSY 15             //busy pin on LoRa device 
+#define SCK 4                 //SCK on SPI3
+#define MISO 13               //MISO on SPI3 
+#define MOSI 2                //MOSI on SPI3
+#define REDLED 33             //pin number for ESP32CAM on board red LED, set logic level low for on
+
+#define LORA_DEVICE DEVICE_SX1280               //this is the device we are using
+
+const uint32_t Frequency = 2445000000;          //frequency of transmissions
+const uint32_t Offset = 0;                      //offset frequency for calibration purposes
+const int8_t  TXpower = 10;                     //LoRa transmit power
+
+//*******  Setup LoRa modem parameters here ! ***************
+const uint8_t Bandwidth = LORA_BW_1600;         //LoRa bandwidth
+const uint8_t SpreadingFactor = LORA_SF5;       //LoRa spreading factor
+const uint8_t CodeRate = LORA_CR_4_5;           //LoRa coding rate
+
+//*******  Setup FLRC modem parameters here ! ***************
+const uint8_t BandwidthBitRate = FLRC_BR_1_300_BW_1_2;     //FLRC bandwidth and bit rate, 1.3Mbs
+//const uint8_t BandwidthBitRate = FLRC_BR_0_260_BW_0_3;   //FLRC 260kbps
+const uint8_t CodingRate = FLRC_CR_1_0;                    //FLRC coding rate
+const uint8_t BT = RADIO_MOD_SHAPING_BT_1_0;               //FLRC BT
+const uint32_t Syncword = 0x01234567;                      //FLRC uses syncword
+
+const uint32_t TXtimeoutmS = 5000;              //mS to wait for TX to complete
+const uint32_t RXtimeoutmS = 60000;             //mS to wait for receiving a packet
+const uint32_t ACKdelaymS = 0;                  //ms delay after packet actioned and ack sent
+const uint32_t ACKdelaystartendmS = 25;         //ms delay before ack sent at array start wrie and end write
+const uint32_t ACKsegtimeoutmS = 75;            //mS to wait for receiving an ACK before re-trying transmit segment
+const uint32_t ACKopentimeoutmS = 500;          //mS to wait for receiving an ACK before re-trying transmit file open
+const uint32_t ACKclosetimeoutmS = 500;         //mS to wait for receiving an ACK before re-trying transmit file close
+const uint32_t DuplicatedelaymS = 25;           //ms delay if there has been an duplicate segment or command receipt
+const uint32_t NoAckCountLimit = 250;           //if no NoAckCount exceeds this value - restart transfer
+
+const uint32_t FunctionDelaymS = 0;             //delay between functions such as open file, send segments etc
+const uint32_t PacketDelaymS = 1000;            //mS delay between transmitted packets such as DTInfo etc
+
+const uint8_t DTSegmentSize = 245;              //number of bytes in each segment or payload
+const uint8_t ARDTfilenamesize = 32;            //size of filename buffer
+
+const uint8_t StartAttempts = 2;                //number of attempts to start transfer before a fail
+const uint8_t SendAttempts = 5;                 //number of attempts carrying out a process before a restart
+
+const uint8_t HeaderSizeMax = 12;               //max size of header in bytes, minimum size is 7 bytes
+const uint8_t DataSizeMax = 245;                //max size of data array in bytes
+const uint16_t NetworkID = 0x3210;              //a unique identifier to go out with packet
+
+const uint16_t SleepTimesecs = 15;              //sleep time in seconds after each TX loop
+const uint32_t uS_TO_S_FACTOR = 1000000;        //Conversion factor for micro seconds to seconds
+const uint8_t PicturesToTake = 1;               //number of pictures to take at each wakeup, only last is sent via LoRa
+const uint32_t PictureDelaymS = 1000;           //delay in mS between pictures
+
+
+#ifdef USELORA
+const uint8_t SegmentSize = 245;                //number of bytes in each segment, 245 is maximum value for LoRa
+#endif
+
+#ifdef USEFLRC
+const uint8_t SegmentSize = 117;                //number of bytes in each segment, 117 is maximum value for FLRC
+#endif
+
+
+// Pin definition for CAMERA_MODEL_AI_THINKER
+// Change pin definition if you're using another ESP32 with camera module
+#define PWDN_GPIO_NUM     32
+#define RESET_GPIO_NUM    -1
+#define XCLK_GPIO_NUM      0
+#define SIOD_GPIO_NUM     26
+#define SIOC_GPIO_NUM     27
+#define Y9_GPIO_NUM       35
+#define Y8_GPIO_NUM       34
+#define Y7_GPIO_NUM       39
+#define Y6_GPIO_NUM       36
+#define Y5_GPIO_NUM       21
+#define Y4_GPIO_NUM       19
+#define Y3_GPIO_NUM       18
+#define Y2_GPIO_NUM        5
+#define VSYNC_GPIO_NUM    25
+#define HREF_GPIO_NUM     23
+#define PCLK_GPIO_NUM     22