Init fork from Stuart Robinson's repo

examples/SX128x_examples/DataTransfer/233_SDfile_Transfer_Transmitter/DTSettings.h

@@ -0,0 +1,64 @@
+/*******************************************************************************************************
+  Programs for Arduino - Copyright of the author Stuart Robinson - 12/03/22
+
+  This program is supplied as is, it is up to the user of the program to decide if the program is
+  suitable for the intended purpose and free from errors.
+*******************************************************************************************************/
+
+#define NSS 10                                  //select pin on LoRa device
+#define NRESET 9                                //reset pin on LoRa device
+#define RFBUSY 7                                //RFBUSY pin on LoRa device
+#define DIO1 3                                  //DIO1 pin on LoRa device, used for sensing RX and TX done 
+#define LED1 8                                  //LED used to indicate transmission
+#define SDCS 30
+#define Monitorport Serial                      //Port where serial prints go
+
+#define LORA_DEVICE DEVICE_SX1280               //this is the device we are using
+
+
+//*******  Setup LoRa Test Parameters Here ! ***************
+
+const uint32_t Frequency = 2445000000;                     //frequency of transmissions
+const uint32_t Offset = 0;                                 //offset frequency for calibration purposes
+const int8_t  TXpower = 10;                                //LoRa transmit power
+
+//*******  Setup LoRa modem parameters here ! ***************
+const uint8_t Bandwidth = LORA_BW_1600;                    //LoRa bandwidth
+const uint8_t SpreadingFactor = LORA_SF5;                  //LoRa spreading factor
+const uint8_t CodeRate = LORA_CR_4_5;                      //LoRa coding rate
+
+//*******  Setup FLRC modem parameters here ! ***************
+const uint8_t BandwidthBitRate = FLRC_BR_1_300_BW_1_2;     //FLRC bandwidth and bit rate, 1.3Mbs
+//const uint8_t BandwidthBitRate = FLRC_BR_0_260_BW_0_3;   //FLRC 260kbps
+const uint8_t CodingRate = FLRC_CR_1_0;                    //FLRC coding rate
+const uint8_t BT = RADIO_MOD_SHAPING_BT_1_0;               //FLRC BT
+const uint32_t Syncword = 0x01234567;                      //FLRC uses syncword
+
+
+const uint32_t TXtimeoutmS = 5000;              //mS to wait for TX to complete
+const uint32_t RXtimeoutmS = 60000;             //mS to wait for receiving a packet
+const uint32_t ACKdelaymS = 0;                  //ms delay after packet actioned and ack sent
+const uint32_t ACKsegtimeoutmS = 75;            //mS to wait for receiving an ACK before re-trying transmit segment
+const uint32_t ACKopentimeoutmS = 250;          //mS to wait for receiving an ACK before re-trying transmit file open
+const uint32_t ACKclosetimeoutmS = 250;         //mS to wait for receiving an ACK before re-trying transmit file close
+const uint32_t DuplicatedelaymS = 10;           //ms delay if there has been an duplicate segment or command receipt
+const uint32_t FunctionDelaymS = 0;             //delay between functions such as open file, send segments etc
+const uint32_t PacketDelaymS = 1000;            //mS delay between transmitted packets such as DTInfo etc
+
+const uint8_t StartAttempts = 2;                //number of attempts to start transfer before a fail
+const uint8_t SendAttempts = 5;                 //number of attempts carrying out a process before a restart
+const uint32_t NoAckCountLimit = 250;           //if no NoAckCount exceeds this value - restart transfer
+
+const uint8_t HeaderSizeMax = 12;               //max size of header in bytes, minimum size is 7 bytes
+const uint8_t DataSizeMax = 245;                //max size of data array in bytes
+const uint8_t Maxfilenamesize = 32;             //size of DTfilename buffer
+
+const uint16_t NetworkID = 0x3210;              //a unique identifier to go out with packet
+
+#ifdef USELORA
+const uint8_t SegmentSize = 245;                //number of bytes in each segment, 245 is maximum value for LoRa
+#endif
+
+#ifdef USEFLRC
+const uint8_t SegmentSize = 117;                //number of bytes in each segment, 117 is maximum value for FLRC
+#endif