Init fork from Stuart Robinson's repo

examples/SX128x_examples/Reliable/222_FLRC_Packet_Monitor/222_FLRC_Packet_Monitor.ino

@@ -0,0 +1,157 @@
+/*******************************************************************************************************
+  Programs for Arduino - Copyright of the author Stuart Robinson - 06/11/21
+
+  This program is supplied as is, it is up to the user of the program to decide if the program is
+  suitable for the intended purpose and free from errors.
+*******************************************************************************************************/
+
+/*******************************************************************************************************
+  Program Operation - The program listens for incoming packets using the FLRC settings in the 'Settings.h'
+  file. The pins to access the lora device need to be defined in the 'Settings.h' file also.
+
+  There is a printout of the valid packets received in HEX format. Thus the program can be used to receive
+  and record non-ASCII packets. The LED will flash for each packet received.
+
+  Serial monitor baud rate is set at 115200.
+*******************************************************************************************************/
+
+#include <SPI.h>
+#include <SX128XLT.h>
+#include "Settings.h"
+
+SX128XLT LT;
+
+uint8_t RXPacketL;                                //stores length of packet received
+int16_t  PacketRSSI;                              //stores RSSI of received packet
+int8_t  PacketSNR;                                //stores signal to noise ratio of received packet
+
+
+void loop()
+{
+  RXPacketL = LT.receiveSXBuffer(0, 60000, WAIT_RX); //returns 0 if packet error of some sort, timeout set at 60secs\60000mS
+
+  digitalWrite(LED1, HIGH);                       //something has happened
+
+  printSeconds();
+
+  PacketRSSI = LT.readPacketRSSI();
+  PacketSNR = LT.readPacketSNR();
+
+  if (RXPacketL == 0)
+  {
+    packet_is_Error();
+  }
+  else
+  {
+    packet_is_OK();
+  }
+
+  digitalWrite(LED1, LOW);
+
+  Serial.println();
+}
+
+
+void packet_is_OK()
+{
+  printReceptionDetails();
+  Serial.print(RXPacketL);
+  Serial.print(F(" bytes > "));
+  LT.printSXBufferHEX(0, (RXPacketL - 1));
+}
+
+
+void packet_is_Error()
+{
+  uint16_t IRQStatus;
+  IRQStatus = LT.readIrqStatus();                     //get the IRQ status
+
+  if (IRQStatus & IRQ_RX_TIMEOUT)
+  {
+    Serial.print(F(" RXTimeout"));
+  }
+  else
+  {
+    Serial.print(F(" PacketError"));
+    printReceptionDetails();
+    Serial.print(F("  Length,"));
+    Serial.print(LT.readRXPacketL());                  //get the real packet length
+    Serial.print(F(",IRQreg,"));
+    Serial.print(IRQStatus, HEX);
+  }
+}
+
+
+void printReceptionDetails()
+{
+  Serial.print(F(" RSSI,"));
+  Serial.print(PacketRSSI);
+  Serial.print(F("dBm,SNR,"));
+  Serial.print(PacketSNR);
+  Serial.print(F("dB  "));
+}
+
+
+void led_Flash(uint16_t flashes, uint16_t delaymS)
+{
+  uint16_t index;
+
+  for (index = 1; index <= flashes; index++)
+  {
+    digitalWrite(LED1, HIGH);
+    delay(delaymS);
+    digitalWrite(LED1, LOW);
+    delay(delaymS);
+  }
+}
+
+
+void printSeconds()
+{
+  float secs;
+
+  secs = ( (float) millis() / 1000);
+  Serial.print(secs, 3);
+}
+
+
+void setup()
+{
+  pinMode(LED1, OUTPUT);
+  led_Flash(2, 125);
+
+  Serial.begin(115200);
+
+  Serial.println(F("221_LoRa_Packet_Monitor Starting"));
+
+  SPI.begin();
+
+  //SPI beginTranscation is normally part of library routines, but if it is disabled in library
+  //a single instance is needed here, so uncomment the program line below
+  //SPI.beginTransaction(SPISettings(8000000, MSBFIRST, SPI_MODE0));
+
+  if (LT.begin(NSS, NRESET, RFBUSY, DIO1, LORA_DEVICE))
+  {
+    Serial.println(F("LoRa Device found"));
+    led_Flash(2, 125);
+    delay(1000);
+  }
+  else
+  {
+    Serial.println(F("No LoRa device responding"));
+    while (1)
+    {
+      led_Flash(50, 50);
+    }
+  }
+
+  LT.setupFLRC(Frequency, Offset, BandwidthBitRate, CodingRate, BT, Syncword);
+
+  Serial.println();
+  LT.printModemSettings();
+  Serial.println();
+  LT.printOperatingSettings();
+  Serial.println();
+  Serial.print(F("Packet monitor ready"));
+  Serial.println();
+}

examples/SX128x_examples/Reliable/222_FLRC_Packet_Monitor/Settings.h

@@ -0,0 +1,31 @@
+/*******************************************************************************************************
+  Programs for Arduino - Copyright of the author Stuart Robinson - 06/11/21
+
+  This program is supplied as is, it is up to the user of the program to decide if the program is
+  suitable for the intended purpose and free from errors.
+*******************************************************************************************************/
+
+//*******  Setup hardware pin definitions here ! ***************
+
+//These are the pin definitions for one of my own boards, the Easy Pro Mini,
+//be sure to change the definitions to match your own setup.
+
+#define NSS 10                                  //select on LoRa device
+#define NRESET 9                                //reset on LoRa device
+#define RFBUSY 7                                //RFBUSY pin on LoRa device
+#define DIO1 3                                  //DIO1 on LoRa device, used for RX and TX done 
+#define LED1 8                                  //On board LED, high for on
+
+#define LORA_DEVICE DEVICE_SX1280               //this is the device we are using
+
+//*******  Setup LoRa Test Parameters Here ! ***************
+
+//LoRa Modem Parameters
+const uint32_t Frequency = 2445000000;           //frequency of transmissions
+const uint32_t Offset = 0;                      //offset frequency for calibration purposes
+
+const uint8_t BandwidthBitRate = FLRC_BR_1_300_BW_1_2;  //FLRC bandwidth and bit rate, 1.3Mbs
+//const uint8_t BandwidthBitRate = FLRC_BR_0_260_BW_0_3;    //FLRC 260kbps
+const uint8_t CodingRate = FLRC_CR_1_0;                   //FLRC coding rate
+const uint8_t BT = RADIO_MOD_SHAPING_BT_1_0;              //FLRC BT
+const uint32_t Syncword = 0x01234567;                     //FLRC uses syncword